HappyModel BNF Mobula7 1S 75mm Brushless Whoop BNF (ELRS / D8, D16 / AFHDS-2A Receiver) Bind-N-Fly

We’re glad to launch our new Mobula7 drone, this time the 75mm whoop based on 1s power. Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1s Will be the best choice in the whoop season.

The world's first 5-IN-1 AIO flight controller with ExpressLRS 2.0, OPENVTX(up to 400mw), 12A Brushless Blheli_S ESC, and Betaflight OSD coming out recently. This is an amazing flight controller for Brushless Whoop. You could get unbelievable RX and VTX ranges by using this flight controller.

The new RS0802 motors come with a new unibell design, use a 1.5mm shaft, and include PCB bottom plate, high efficiency, and much more reliable. New onboard OpenVTX, max power up to 400mw, provides RCE and PIT mode, it was very useful for a race event.

Features:

• X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and Openvtx
• VTX Power up to 400mw
• ELRS V2.0 Support
• NEW RS0802 KV20000 motors
• Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
• Smooth and powerful
• Compatible for 1S Lipo/LIHV
• Recommend 1S 450mah/550mah/650mah battery(Not include)

• Brand Name: Happymodel
• Item Name: Mobula7 1S 75mm Micro FPV whoop drone
• Wheelbase: 75mm
• Size: 99mm*99mm*40mm
• Weight: 24g

• Mode: RS0802 KV20000
• Configu-ration:9N12P
• Stator Diamter:8mm
• Stator Length:2mm
• Shaft Diameter:Φ1.5mm
• Motor Dimension(Dia.*Len):Φ10.5mm*13.5mm
• Weight(g):2.0g
• No.of Cells(Lipo):1S only

• Weight:0.24g
• Material:PC
• Pitch:1 inchProps Dia:40mm
• Center Thickness:5mm
• Center Hole Dia:1.5mm

• X12 ELRS V1.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
• X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
• X12 PNP V1.0 flight controller with external TBS CRSF Nano receiver Target: CRAZYBEEF4DX
• X12 PNP V1.0 flight controller without onboard receiver Target: CRAZYBEEF4DX
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU6000 or ICM20689 or BMI270(SPI connection)
• Mount hole size: 25.5mm*25.5mm
• Power supply: 1S battery input (DC 2.9V-4.35V)
• Built-in 12A(each) Blheli_S 4in1 ESC
• Built-in Betaflight OSD(SPI Control)
• Built-in 5.8G OpenVTX 0mw~400mw
• Built-in ExpressLRS 2.4G,Frsky D8/D16
• Built-in voltage detection
• Built-in current sensor

• Power supply: 1S LiPo/LiPo HV
• Current: 12A continuous peak 15A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: Z_H_30_REV16_7.HEX
• Default protocol: DSHOT300
• Support Bluejay firmware

• Packet Rate option: 50Hz/150Hz/250Hz/500Hz
• ExpressLRS Firmware version: V2.0
• RF Frequency: 2.4GHz
• Antenna : SMD antenna
• Telemetry output Power: <12dBm
• Receiver protocol: SPI ExpressLRS
• Compatible with ExpressLRS V2.0 TX Module
• Couldn’t flash separately ExpressLRS firmware

• SPI BUS receiver Frsky D8 compatible
• Compatible Non-EU transmitter D8 model
• Channels: 8ch
• No ground interference ( Transmitter and receiver 1 m from the ground): 200meterFailsafe support

• Firmware version: OPENVTX
• Smartaudio v2.1
• PIT Mode support
• RCE Mode support
• Channels:48ch
• Transmitting Power: 0/RCE/25mw/100mw/400mw
• Power supply: DC 5V
• Current (5v):650ma~1000ma

• Model: Nano 3
• Image Sensor: 1/3″ CMOS
• Horizontal Resolution: 800TVL
• Lens : 2.1mm(M8) FOV 150°
• Signal System: NTSC
• S/N Ratio: >50dB
• Electronic Shutter Speed: Auto
• Auto Gain Control (AGC): Auto
• Min. Illumination: 0.01Lux@1.2F
• D-WDR: Auto
• Day/Night: Color
• Power: DC 3-5.5V
• Current: 110mA@5V 120mA@3.3V
• Housing Material: ABS
• Net Weight: 1.2g
• Dimensions: L14mm*W14mm*H9mm

• Mobula7 1S 75mm Whoop Drone RTF (ELRS / FRSKY / FLYSKY)
• 1x 1S parallel charging board
• 1x Propeller removal tool
• 1x Extra camera canopy